Vehicle Electrification + Environmental Test Center


Get to Market Faster

The Allison Vehicle Electrification + Environmental Test Center (VE+ET) is an industry-leading facility that allows OEMs, body builders, suppliers and end-users to satisfy their medium- and heavy-duty vehicle testing needs in a single, environment-controlled location year-round.

Customers are now facing increasing system complexity, expanding regulatory requirements and higher demand for ever-faster time-to-market requirements. Allison has you covered. The VE+ET’s one-stop chassis testing can shorten your product development cycles dramatically, facilitating efficiency and ultimately cutting down the costs of bringing your product to market. The VE+ET provides vehicle system development and validation in repeatable, reliable and seasonally independent conditions to get the test results you require.

Results That Matter

The VE+ET’s highly controlled environment enables an enhanced level of virtual product development, driving lower costs. Results from the VE+ET are ideal for developing sophisticated, highly correlated simulations and models so design decisions happen early in the cycle, before prototype hardware investments.

Test Confidently

The VE+ET is secured, operated and managed independently from Allison Transmission, Inc. keeping customer IP, data and property secure and confidential.

Our Export Compliance Program is robust and comprehensive, ensuring that our military customer’s export controlled technology is safeguarded.

Applications Supported

  • On-highway vehicles
  • Off-highway vehicles
  • Conventional fuel vehicles
  • Electric & Hybrid vehicles
  • Alternative fuel vehicles
  • Wheeled defense vehicles
  • Generator (Gen) Sets
  • More...

Types of Vehicle Testing

  • Vehicle and System Performance/Development/Validation Testing
  • On Board Diagnostic (OBD) Development
  • Product Troubleshooting
  • Regulatory (EPA 40 CRF Part 1066) Compliant
  • Fuel Economy
  • Controls Software Performance/Development/Validation
  • Simulation and Analytical Model Validation/Correlation
  • Thermal (HVAC, Cooler, Battery Life/Efficiency/Charging)
  • BEV Development (Thermal Performance, Charging, etc.)


Cold Environment + Extreme Winter

-54°F / -48°C Soak chamber + In Dyne Environmental. Maintain Cell Temperature up to 800HP Thermal Load

Altitude up to 18,000 Feet

Mountain roads/altitude up to Military specs. -40 < 70C inlet air temperature with humidity control up to 1,000HP

Hot Environment + Extreme Summer

125°F / 51°C Soak chamber + In Dyne Environmental. Maintain Cell Temperature up to 800HP Thermal Load
Emmisions Icon

Emissions Testing

EPA 40 CFR Part 1066 Compliant Testing

Two Raw Sampling Measurement, Compliant to 4km (13k ft) elevation

2 Chassis Dynamometers

Heavy-Duty AWD Regulatory Dyne Assemblies with capacity of 4,000-82,000 lbs. GVW

MD wheel base 110 inches - 335 inches; 101kN max driving force (Front 2x250kW, Rear 2x450kw)

HD wheel base 138 inches - 335 inches; 209kN max driving force (Front 450kW, Rear 450kw)

Electric / Hybrid / e-Axle Vehicle Testing

Vehicle System Emulation

Two 250kW 800V E-Motor/Inverter Testing

Level 1, 2, and 3 chargers onsite

Secure + Confidential

Environment for Data and Information

Data is secured and confidential throughout process
0:00 / 0:00


How much will the facility be available to the market?

The facility’s use is intended for roughly 50% Allison work and 50% non-Allison work (available to the market).

Can I perform my own testing at your facility?

We will operate the following services:

  • Test vehicle moving, test preparation, and maintenance
  • Test vehicle driving on/off dyno
  • Engineering support

The customer is allowed to do the following:

  • Test vehicle preparation and maintenance
  • Customers can ride in the vehicle while our techs drive.
  • Engineering support
How do I know my information will not be shared within Allison or other competitors?

Allison Transmission has separately secured data systems, management systems, and sales systems for the VE+ET. Allison Transmission is even considered an outside customer to AIS.

Can I send my vehicles to the VE+ET for testing without any of my own support staff?

We are equipped to perform your testing based on test plans and hardware alone. A technical review will be had for each of these milestones:

  • During the quoting process
  • Kick-off meeting after PO awarded and scheduled
  • Test setup confirmation (if needed)
  • Post process data analysis
Am I only able to perform cold starts? How long until the test cell heats up when running?

Not at all. The chamber will maintain ambient temperatures (-50°C < +50°C) continuously as you run your vehicle under heavy loads. This also includes humidity control. The altitude conditions will also be held under heavy power from sea level to 5km of elevation (-40°C < +70°C inlet temperatures).

Can I test hot and cold on the dyne with altitude?
Yes.  The VE+ET’s altitude capability is fully operational across the range of our dyne chamber’s hot environment and cold environment capabilities.
Can I get my test data live, if I send the vehicle for you to perform my testing?
Yes.  While we look forward to collaborating with your teams on-site at the VE+ET,  the VE+ET has live collaboration capabilities that enable our customers to participate in testing from remote locations; saving our customers the cost of entire engineering teams traveling to the test site. 
Can I use your cold and hot testing chambers even if my product is not a vehicle?
Yes.  While the VE+ET was designed to enable vehicle development and testing, our cold environment and hot environment soak chambers can accommodate non-vehicle products.  Please contact us to discuss your unique needs determine how the capabilities of the VE+ET can provide a solution.

VEET Wordmark CMYK_Outlines

Contact Us

To get your vehicle to market quickly, you need repeatable, reliable and seasonally independent vehicle testing. You can get it all in one location at the VE+ET. Get a head start by contacting us below.

Need Help? Download our HOW-TO VIDEO for a brief demo on how to submit a Service Inquiry and Request For Quote. (MP4 player required)